Tony’s Scrapbook; Boeing 247 Transport

Passengers waiting to board the Boeing 247

The Boeing 247 revolutionized civilian air travel through high speed, passenger comfort, and futuristic designs not seen by the previous airliners, virtually rendering them obsolete in a single day. Some examples of earlier airlines consisted of the Ford Tri-motor “Tin Goose,” the Fokker F-10 Super Trimotor, and the Curtiss Condor biplane. These airliners were usually underpowered for their size with open engines and large fixed landing gear resulting in a large drag coefficient and overall poor performance with long flight times between destinations.

Newspaper clipping from Tony’s scrapbook dated January 1933

The first flight of the Boeing 247 happened on February 8, 1933, and enters into service with United Air Lines on March 30, 1933, launching United well above the competition. The Eastern division of United received the first delivery in April. By the end of September, the entire fleet is in service operating in all of the United Air Lines territories. The 247 sets the trend for future airlines with United on top and momentarily deems all other current airliners out-of-date for about a year until the Douglas DC-2 entered the market on May 11, 1934, for TWA.

United ordered sixty planes in 1932 after seeing a final version model with the first batch of fifteen airplanes entering production by mid-1932. Boeing built much of the 247’s components in secrecy because United Air Lines didn’t want the other airlines knowing of their intent on the future of airline travel.

Boeing 247

Prototyping of the 247 began in 1930 and evolved from a combination of Boeing’s previous single-engine high-performance mail plane, the Model 200 “Monomail,” and it’s twin-engine military bomber, the Model 246/Y1b-9A.

Boeing “Monomail”

On May 6, 1930, the Boeing “Monomail” completes a successful test flight powered by a fully cowled Pratt & Whitney “Hornet” B radial engine rated at 575 hp with a maximum cruising speed of 140 mph at sea level. This new all-metal airplane has a cantilever low-wing design with retractable landing gear and three mail compartments totaling 220 cubic feet.

Boeing Y1B-9. (U.S. Air Force photo)

The United States Army Air Corps (USAAC) ordered five Boeing YB-9 bombers for assessment and tested it against other competitors’ aircraft, all competing for a new military contract. Boeing produces the YB-9 as an upgraded model based on their earlier experimental designs, the 214 and 215 models. Powered by two Pratt & Whitney 600 hp “Hornet” engines, this cantilever low-wing monoplane with retractable landing gear can carry five crew members, two machine guns and has an external explosive payload limit of 2200 pounds.

Martin B-10

As impressive as the Boeing YB-9 is, it has its limitations, especially without any internal bomb bay. The Martin B-10 bomber is a better fit, and the Glenn L. Martin Company of Baltimore, Maryland, wins the contract.

Boeing YB-9 (courtesy Ray Crupi)

Boeing retains the cantilever low-wing twin-engine monoplane construction of the YB-9 in designing the 247 but completely redesigns the fuselage for passenger transport. Designers add seating for ten passengers and a flight crew of three, including the pilot, a co-pilot, and a flight attendant. The wing spars of the internally braced cantilever wings became a tripping hazard where passengers had to step over them to traverse the cabin forward and aft.

Pratt & Whitney R-1340 Wasp
Pratt & Whitney R-1340 “Wasp” engine (courtesy Insomnia Cured Here)

The Boeing 247 is the first airline with twin direct-drive supercharged Pratt & Whitney S1D1 “Wasp” engines rated at 550 hp at 5000 ft spinning three-bladed fixed pitch propellers and has a top speed of 180 mph. The retractable landing gear attaches under each engine mount and folds into each wing’s leading edge engine nacelles. The all-metal construction of the 247 proves durability, safety, and efficiency, which reduces the previous transcontinental flight between New York and San Francisco by seven hours, with only seven stops in less than twenty hours. United Air Lines revenue increases dramatically because of their fast and dependable schedules, passenger comfort, and aggressive advertising campaign, earning the title “Three-Mile-A-Minute-Transport.”

Boeing 247
Boeing 247 (courtesy planephotoman)

Boeing soon discovered that replacing the fixed-pitch propellers with variable-pitch props improved performance and added 10mph to the already impressive cruising speeds. The demand is high for the Seattle Washington Boeing Airplane Company, a division of the United Aircraft & Transport Corporation, to produce sixty aircraft on time. Boeing soon increases its workforce to thirteen hundred workers and sublets work to Stearman Aircraft in Wichita, Kansas, another division of United, to assemble the landing gears, tail wheel assembly, and various small packs for the 247.

Interior seating of the Boeing 247

The 247’s semi-monocoque fuselage’s main cabin has five seats on each side and seating for the flight attendant located towards the aisle’s end at the plane’s rear. The 20′ x 6′ high cabin features separate heating and air vents for each passenger, reclining seats, dome and reading lights, and convenient ashtrays. Gray-green fabric adorns the interior walls, covering insulation layers and soundproofing, making for a pleasant flight with complimenting green whipcord patterned fabric upholstered seats.

A businessman prepares to climb three portable steps to board the 10-passenger Boeing 247 operated by Varney Air Lines, part of the United system in the 1930s. A flight attendant stands at the ready. Once aboard the airliner, they will have to step over the wing spars to reach the front of the cabin. (Frederick A. Johnsen collection)

A right-side main entry door, aft of the right wing’s trailing edge, allows access to the welcoming cabin by traversing a few steps on a short rolling ladder. Once inside, one must carefully step over the interior wing spars that intersected the floor while proceeding towards the passenger cabin’s front. The wing spar is an inconvenience, but the passengers soon accept it as visual reassurance of the strength and engineering behind the new 247 design. On the left side, a small lavatory and stewardess pantry that can serve light meals during the flight sits across from the rear main entry door. A tail section cargo bay is easily accessible through a door to the left of the main entrance with a maximum capacity of 65 cu ft. A second 60 cu ft cargo area is located behind the aircraft’s nose but can only be accessed externally.

Notice the forward slanting windscreen on this early 247

The forward-slanting windscreen quickly identifies the cockpit of the early 247’s as opposed to the later models with backward slanting windshields, but I’ll cover those other models later. All cockpits have dual controls, sliding side windows, two-way radios, state of the art navigational instruments, night-flying equipment, and a radiophone in the nose compartment’s upper area.

1933 Boeing 247

The stub wing is an integral part of the fuselage that firmly supports the massive landing gear, engine mounts, and nacelles. Fuel tanks also reside in the wing stub, one on each side with an additional 70-gallon reserve in the right tank. The smooth metal skin consists of anodized aluminum sheeting riveted to internal framing, resulting in a grayish exterior color often left unpainted. The all-metal tail section uses a similar cantilever design where internal bracing strengthens the horizontal stabilizer, but later models switch to fabric-covered rudders and elevators to reduce weight.

Boeing 247-D at the Smithsonian Institution National Air and Space Museum. Photo by Eric Long. Photo taken on March 19, 2018.

Newly designed “trim tabs” added to the ailerons’ trailing edges, elevator, and rudder allow the pilot to trim the aircraft during flight. Offset hinges installed on both the rudder and elevator provide additional aid to the pilot by reducing the amount of force needed at the control wheel to steer such a large airplane with substantial control surfaces.

Boeing 247 9444
Boeing 247 (courtesy Del Hoffman)

This impressive aircraft measures 51′ 4″ in length and has a height of 12′ 6″ with a 74′ wingspan. It has an empty weight of 8370 pounds with a useful load of 4280 pounds, bringing the maximum gross value to 12,650 lbs. The top speed is 182 mph at 5000 ft, but a comfortable cruising speed of 161 mph at the same altitude is ideal. Climbing to 8000 ft is achieved 10 minutes after takeoff, with the initial rate of climb decreasing from 1070 ft after the first minute to 830 ft at 5000 ft. The maximum fuel capacity is 265 gallons when the tanks are filled to the caps when needed but usually run below that level resulting in 203 gallons per flight. Cruising range is about 600 miles when the pilot can manage the fuel-hungry “Wasp” engines to sip just 30 gallons each per hour.

Boeing sees room for improvements in powering the 247 and is confident that the airframe is structurally sound to handle larger engines. After discussions with Pratt & Whitney, the two reach an agreement that Boeing will modify the 247 as a test plane for their new “Twin Wasp Junior” engines currently in development and used exclusively as an executive transport for the officers of the United Aircraft & Transport Corporation. The 247-A is born.

Pratt & Whitney R-1535-96 Twin Wasp Junior
Pratt & Whitney “Twin Wasp Junior” engine (courtesy Daniel Berek)

On September 14, 1933, Bernard “Benny” Whelan piloted the newly designed 247-A airliner’s first flight. “It’s a delight to fly with the increased power,” Benny remarked after landing and is impressed with the redesigned engine nacelles and broadened shrouds that now cover the more in-depth double row engines. He also enjoys seeing the new plush interior, now with spacious seating for six passengers, and still retains the rear lavatory and small kitchenette. Larger fuel tanks increase the capacity to 356 gallons extending the cruising range to about 1000 miles and reduce the number of stops on longer flights. The Pratt & Whitney SGR-1535 “Twin Wasp Junior” engine is rated at 625 hp at 2400 rpm at 7000 ft.

Engine testing continued with the installation of Pratt & Whitney’s newest development, the S1A1G engine rated at 660 hp at 2400 rpm at 7000 ft. This upgrade added 695 lbs to the total gross weight while retaining the same performance level as the previous SGR-1535 engine. Only one 247-A is produced for the sole purpose of testing and logged more than 3000 hours of flight time from 1933 to 1942 from its hanger based in Hartford, Connecticut. In 1947 the 247-A was scrapped but not before an accident-free career spanning 14 years, including two mercy flights saving both people’s lives and valuable data collected during those flight years.

The 247-A “Special” variant of the 247-A features higher torque engines, the Pratt & Whitney SA7G rated at 655 hp, increasing the gross weight to 13,650 lbs. That’s a 1000 pound increase from the original 247s gross weight of 12,650 lbs! This new 247-A “Special” also tests previous engines used in the 247-A, the 625 hp SRG-1535, and the 660 hp S1A1G with different passenger configurations leading up to the 247-D.

The 247-D is the last variation of the easily adaptable 247 in Boeing’s goal to stay competitive and easily identified by its backward sloping windshield. New supercharged Pratt & Whitney 550 hp S1H1-G “Wasp” engines fit in larger, more streamlined nacelles with close-fitting NACA cowls that reduce drag and increase speed. The 3:2 geared prop shaft spins the Hamilton-Standard “Controllable Pitch” propellers for better thrust, replacing the direct-drive fixed pitched props of the earlier 247s. The 247-D can carry ten passengers with up to 750 lbs of baggage and a flight crew of three, retaining the original configuration of the previous 247s but with an increased payload weight. Improvements to the cabin provide passenger comfort and convenience while the pilot enjoys an increase in performance and updated controls, making it easier to fly. Plus, the revised instrument panel, including an optional Sperry autopilot and Goodyear deicer boots on all leading edges. The aircraft can maintain the “Three-Miles-A-Minute” status at 3/4 throttle compared to the first 247s needing full throttle to achieve the same results due to the reduced drag and larger engines.

NC13369 - BOEING 247   Washington
Boeing 247-D (courtesy Vin LK)

Pratt & Whitney S1H1-G “Wasp” engines are rated at 550 hp at 2200 rpm at 8000 ft, increasing the service ceiling from 4500 ft to 11,500 ft with one engine out under full payload compared to the earlier S1D1 engines. Gross weight remains consistent at 13,650 lbs, but the maximum speed increases to 202 mph at 8000 ft with a cruising speed at 3/4 throttle of 184 mph at the same altitude. The climb rate in the first minute is 1150 ft at sea level and can reach 11,000 ft in ten minutes with a service ceiling of 25,400 ft. Cruising range reduces to 800 miles due to the smaller fuel tanks needed to offset the extra weight of 10 passengers and their luggage, burning 66 gallons of fuel per hour at cruising speed. The redesigned all-metal tail group features additional internal strengthening under the aluminum skin and improved control surfaces. Fabric-covered rudder and elevator installed with offset hinges replace the metal cover units to reduce weight and lighten the force at the pilot’s control wheel.

247-D “Adaptable Annie” and Paul Garber

On October 20, 1934, Roscoe Turner and Clyde Edward Pangborn entered a modified 247-D “Adaptable Annie” into the MacRobertson Centenary Air Race celebrating Melbourne, Australia’s 100th anniversary. This aircraft had additional fuel tanks installed into the fuselage and upgraded navigational equipment for the grueling 18,000-kilometer trip.

The flight path traversed over three continents, nineteen countries, and seven seas with five stops in Baghdad, Allahabad, Singapore, Darwin, and Charleville starting from Mildenhall, England, and finishing in Melbourne, Australia. The race has two divisions, speed, and handicap with no limitation on the aircraft, engines, or flight crew size. Turner and Pangborn finish the race in 92 hours and 55 minutes, coming in third behind a Douglas DC-2 entered by KLM piloted by the flight crew K.D. Parmentier, J.J. Moll, B. Prins, C. Van Brugge, and carrying three passengers. The DC-2 finished the race in 90 hours and 13 minutes and won the handicap division. This race showcased the strength and durability of stressed metal airplanes and that air travel over long distances is possible, making international air transport a safe alternative.

CF-JRQ (Chevron Standard)
Boeing 247-D Chevron Standard Limited (courtesy Reinhard Zinabold)

In Seattle, Washington, the Boeing factory builds thirteen new 247-Ds while the United Air Lines Overhaul Base in Cheyenne, Wyoming, converts existing 247s in their service fleet. By 1937, the 247-D finds itself becoming obsolete through fierce competition and new advances in aviation development, especially in the Douglas DC series of airliners. United decides to lease or sell most of its service fleet of 247-Ds to smaller airline companies who are more than happy to acquire them. In 1942, 27 are called into duty by the USAAF and rebranded as the C-73 for military use. By 1944, undamaged deactivated planes return to their former owners or lent to foreign countries temporarily and eventually return to the U.S.

Boeing C-73, at Hammer Fld
Boeing C-73 at Hammer Field (courtesy SDASM Archives)

Thanks for making it to the end and if you enjoyed reading this post, please sign up below to follow me and you will be notified by email when I upload a new post. See you soon!


A recent tragedy that resulted in two fatalities from a crash of an airplane that I’m not familiar with, a SOCATA TBM 700, impacted a wooded area near Pembroke, New York, October 2, 2020. A prominent attorney in the Buffalo, New York area, and his niece were the only people on board, and thankfully no other injuries are reported at the crash site. My heart is heavy with sorrow for the family, and I extend my thoughts during this most difficult time. My family and I personally experienced similar hardships, more than I would care to remember, but I find that time is a great healer, allowing us to cope better and understand our loss.

Socata TBM 700
SOCATA TBM 700 (courtesy Benjamin Ballande)

In 1990, the TBM 700 series entered the civilian aviation market as the first certified, both with the FAA and French DGAC (EASA), pressurized single-engine turboprop aircraft in the world, labeled as the TBM 700A model. A list of impressive features includes; a 1305 nautical mile range, a maximum cruising speed of 300 knots, a useful load of 1347 pounds, and a short take-off or landing field length of 2133 ft. The TBM 700 can easily land on a 2800 ft runways or less, making this airplane far more accessible to shorter strips than business jets. Couple this with the capacity to carry six passengers in a luxurious cabin, and the Canadian’s performance made Pratt & Whitney PT6A-64 turbine engine; the result is a legendary performer. The PT6A-64 has a thermodynamic power rating of 1570 ESHP with a flat rated power of 700 shaft horsepower. A 91″ diameter Hartzell four-bladed hydraulic propeller provides the thrust with constant speed, automatic full feathering, and reverse thrust control. The minimum landing distance is reduced to 1640 ft using reverse thrust. Net weight is 4100 pounds with a maximum take-off weight of 6579 pounds. The climb rate is 11 minutes 45 seconds to 20,000 ft and 20 minutes 30 seconds to the maximum certified ceiling of 30,000 ft.

Delta Air Lines A350-941 N501DN at KCMH
Delta Air Lines A350-941 (courtesy Lunken Spotter)

Let’s take a moment to talk about turbines and the differences between a turboprop engine, like the one used on the TBM 700, and a turbofan engine used on most commercial airliners that we are most familiar with seeing. Think of your classic commercial jet airliner and the two turbofan engines, one mounted on each wing.

Turbofan Engine (courtesy

When ignited fuel exits the combustion chamber, the high-pressure explosion is forced through the rear turbine, causing it to spin, driving the shaft-mounted front compressor blades and duct fan, which in turn produces thrust, in very simplified terms. The rearward thrust propels the aircraft forward, creating lift generated by the wings and allowing the flight’s fundamental principle.

Turboprop Engine (courtesy

A turboprop engine is similar to a turbofan engine except that the shaft connected to the rear turbine spins a front reduction gearbox, in place of the duct fan, that turns the propeller. I know it’s a bit more complicated than that, but I think you get the idea. Why am I bringing this up, you ask? Because I feel it’s important to understand what a turboprop engine is and why the TBM 700 series aircraft uses it instead of using the more common piston engine found on smaller single-engine airplanes.

SOCATA TBM 700 (courtesy AOPA)

Turbine powered airplanes can fly at high altitudes. The desired operating height is between 20,000 and 30,000 ft to optimize the relatively low-efficiency rate compared to a piston engine plane, which is usually limited to under 15,000 ft. Turbine engines are smaller and lighter than comparable piston engines and are more reliable. They are also more expensive because of the high-quality parts used and rigor needed to produce this appreciable power plant. The TBO or time between overhauls is extended for a turboprop because it consists of fewer moving parts than a piston engine, meaning less downtime between flights. Turboprop engines use superior metals to withstand the high operating temperatures and extreme turbine revolutions requiring precision balancing, which factors into the higher costs over a piston engine. Fuel is another benefit of a turboprop where jet fuel is more readily available than typical avgas used in piston engines, making refueling easier during long flights.

Socata TBM 700
SOCATA TBM 700 (courtesy Benjamin Ballande)

The TBM 700 series’s airframe consists of incorporating various aluminum and steel alloys, including titanium. Advanced composite material strengthens the airframe’s structural integrity, allowing durability at the lowest possible weight while maintaining reduced manufacturing costs. Failsafe engineered techniques incorporated on all TBM airframes include using multiple load paths, a crack-stopper band, and minimizing the number of small access panels to maximize sub-system reliability and structural life.

F-RAXM (XM-111) Socata TBM-700A French Army LDE
SOCATA TBM 700A French Army LDE (courtesy Philippe Brillon)

In 1992, the French Air Force and French Army Aviation received the TBM 700A model aircraft delivery from SOCATA to replace the obsolete Morane MS 760 Paris Jet. The French military pilots reported that the TBM 700A is “simple to master, a dream to fly and superior performance characteristics across the entire flight envelope.” The French Armed forces have also operated the TBM 700A in varied environments, including combat zones, accumulating around 600 flight hours per plane annually, accomplishing a wide range of light cargo and VIP passenger missions. The French national flight test center (CEV) also received a TBM 700A along with an order of three delivered to the Indonesian government for their country’s airfield navigation aid calibration.

160 | Socata TBM-700B | French Army
SOCATA TBM 700B French Army (courtesy Chris Globe Photography)

In 1999, the TBM 700B model’s introduction showcased a sizeable cargo door with an added pilot entry door as an option. The French Army Aviation adds three 700B models to their fleet, increasing the total service to 28 aircraft in 2002. The certified ceiling raised to 31,000 ft due to the addition of a gaseous backup oxygen system with EROS quick donning masks.

Socata TBM 700C2 C-GPQB
SOCATA TBM 700c2 (courtesy Olivier Lacombe)

2003 is the last year of upgrades to the TBM 700 platform with the TBM 700c2 model. The maximum take-off weight increases to 7394 lbs with a payload increase of 865, including full fuel tanks and a rear external luggage compartment. The model 700C, which precedes the 700c2, is identical except for lacking the reinforced landing gear, which reduces the maximum take-off weight and the 20G cabin seats. The structural modifications of the 700c2 include a reinforced airframe, a strengthened landing gear, seats certified to withstand 20G’s in the event of a crash, upgraded avionics, and a new cabin environment that sets the standards in executive travel.

SOCATA TBM 850 (courtesy Alan Wilson)

The TBM 700 platform is so successful that EADS SOCATA launches the TBM 850 Legacy in 2006 using an identical airframe. Still, featuring a turboprop engine, the new Pratt & Whitney PT6A-66D replaces the PT6A-64 and increases the ratings to 1825 ESHP with a flat rated shaft horsepower of 850.

I would end this article with the TBM 700c2, but SOCATA has such an exciting past that I couldn’t resist the urge to dive deep into their history. We will need to go back to the early 1900s, a time that I find so fascinating since I started investigating the news clippings in my father’s scrapbook, and I hope you’ll join along for another stroll down aviation history lane.

The first Bleriot XI in 1909 (courtesy Federation Aeronautique Internationale)
Louis Bleriot in his aircraft just before takeoff for his cross-channel flight, 25 July 1909 (courtesy Federation Aeronautique Internationale)

Morane-Saulnier formed the French manufacturing company on October 10, 1911, when Raymond Saulnier composed a partnership with the Morane brothers, Leon and Robert. Saulnier previously worked for Louis Bleriot as an engineer starting in May 1908 but decides to leave in October 1909 to form his short-lived airplane company, demised with a financial burden. While working for Louis, he helped design the Bleriot XI, where Louis successfully flew it 22 miles across the English Channel from Calais, France, to Dover, England, on July 25, 1909, in 36 minutes 30 seconds. Louis is instantly famous, becoming the first person to fly an airplane across the English Channel! Saulnier later meets Bleriot pilot Leon Morane towards the end of 1910 through his business associate, Gabriel Borel, representing the Bleriot plane. He soon meets Leon’s brother Robert, and the three agree to form the successful Morane-Saunier company.

Louis Bleriot after landing, 25 July 1909 (courtesy Federation Aeronautique Internationale)

Roland Garros and Morane-Saulnier type H monoplane (courtesy
Morane-Saulnier type H (courtesy Australian War Memorial)

Eager to beat Louis Bleriot’s English Channel flight, Saunier begins working on a new design, the Morane-Saulnier type H airplane and completes a test flight in early 1912. The aircraft is a great success, and on September 23, 1913, company pilot French aviator Roland Garros completes the first non-stop flight across the Mediterranean from Frejus, France, to Bizerte, Tunisia.

Morane-Saulnier type L with parasol wing (courtesy

Garros enlisted as a pilot with the approaching World War and soon began working on arming a plane. He was tired of trying to shot the enemy planes with his pistol while on reconnaissance missions. There he modified a Morane-Saulnier type L parasol monoplane by installing a Hotchkiss machine gun firing 8mm solid copper bullets through the propeller’s rotation. The only problem, and a major one, is the lacking of a mechanized timing system between the machine gun and the propeller’s rotation preventing the bullets from striking the prop. Garros realizes this is a problem, to say the least, and adds triangular steel plates to the propeller blades to deflect any bullets that may hit. This technique was not very efficient but still gives Garros the upper hand in piloting a more lethal aircraft than his enemies at the start of the war. Saulnier is impressed with Garros’s design that he files for a patent in April 1914.

Garros deflector system (courtesy

In April 1915, Garros tested his new machine gun design during actual air combat and obtained three victories in fifteen days. Unfortunately, his luck didn’t last long, and he finds himself behind enemy lines when German anti-aircraft fire damage his plane while flying over Belgium. With no time to destroy his aircraft and keep his machine gun design secrete, German soldiers, capture him becoming a prisoner of war for three years. The Germans can now study his machine gun design on his damaged aircraft, which they ship off for Anthony Fokker to examine. Fokker is currently under contract to build airplanes for Germany, the Fokker Eindecker, and asked to add this machine gun design to their planes. At first, he notices the simplicity of the metal plates mounted onto the propeller blades, but then instantly realizes the solution is to have the propeller fire the gun. Since the propeller rotates at 1200 rpm and the gun fires at 600 times per minute, Fokker decides to add a cam off of the engine crankshaft to fire the gun every other turn. Brilliant! And in three days, he has developed a synchronized machine gun system capable of firing bullets cleanly through a spinning propeller.

Fokker Eindecker (courtesy John W.R. Tayler)
Fokker Eindecker E.III (courtesy Karsten Palt)

Morane-Saulnier type N Serial No. 186 (courtesy

Raymond Saulnier designed many airplanes for his company, and Morane-Saulnier produced more than 140 models with a significant number produced between the two wars. Perhaps the most recognized are the MS 130 from the 1920s and the MS 230 from the 1930s, but I am particularly fond of the 1914 type N Bullet.

MS 406
MS 406 (courtesy Massimo Foti)

In 1938, the MS 406 debuts as a famous French fighter and were France’s most numerous aircraft during WW II, capable of over 300 mph with a dive speed over 450 mph without any structural failure. The MS 406 also incorporates Saulnier’s patented sliding ejectable cockpit developed in 1937. I hope the pilot’s uniforms came with an extra set of pants!

MS 760 Paris
MS 760 Paris (courtesy yvon cozannet)

After testing in 1954, Morane-Saulnier introduced the twin-turbine MS 760 Paris in February 1959 as the first four-passenger jet sold as a military trainer or civilian business plane. Variants include the MS 760B Paris II and the MS 760C Paris III.

Morane Saulnier MS 760C Paris III n° 01 ~ F-BLKL
MS 760C Paris III (courtesy David Biscove)

Raymond Saulnier manages to operate his company for more than fifty years successfully but decides to fill for bankruptcy in 1962 due to decreased sales. Henry Potez took over the bankrupted Morane-Saulnier on January 8, 1963, and after a short period, becomes a subsidiary of Sud-Aviation on May 20, 1965. The name changed in 1966 to SOCATA, an acronym for Societe de Construction D’Avions de Tourisme et D’Affaires or “Company for The Construction of Aircraft for Tourism and Business.”

Multinational aerospace conglomerate EADS purchases SOCATA in 2000 as a solely owned subsidiary and rebrands the company name to EADS SOCATA. Daher, a French technology business, negotiates a deal with EADS to purchase 70% of its shares on November 3, 2008. In June 2014, Daher acquired the remaining shares from EADS and rebranded the company in March of 2015 from EADS SOCATA to Daher.

The name Henry Potez should be familiar to you because I touched briefly on him and his Potez 25 biplane that Jean Mermoz flew over the Andes Mountains in 1929. If not, read more about him in my post, Tony’s Scrapbook; Jean Mermoz.

Thanks for taking the time to read this through to the end and if you enjoyed reading this post, please consider following me by signing up to be notified via email when I upload a new post. Cheers!

Tony’s Scrapbook; Northrop Delta

Northrop XB-35 (courtesy Northrop)

John Knudsen Northrop, aka “Jack” Northrop, doesn’t need an introduction, and I have fond memories of the first time seeing his XB-35 flying wing on the cover of an old magazine that my father had been reading the night before. I must have been five or six at the time, and that single image still has lasting impressions for me to this day. I’ve always know Northrop’s involvement with military aircraft, but never seemed interested or paid much attention to his past or previous designs. Because I found the XB-35 so fascinating, I never gave it much thought about the career path that this legendary man had taken in creating an array of distinguishing aircraft.

In the above news clipping dated January 1933 by my father, a Northrop Delta illustrates the future sixteen-hour coast-to-coast schedules for TWA’s passenger transport with a delivery date of March 1 of fifteen aircraft. The Delta can carry eight passengers and 1,000 pounds of freight at 187 mph, as stated above and powered by a 700 hp Wright engine. These details seem vague to me, and I thought a thorough investigation of the Northrop Delta is necessary.

Jack Northrop (courtsey Northrop Grumman Corp.)

The Northrop Delta came about from the partnership of Jack Northrop and his good friend Donald Douglas of the Douglas Aircraft Corporation. Douglas hired Northrop in 1923 to design the fuel tanks for the Douglas World Cruiser. Their relationship was complicated, and Northrop decided to part ways in 1926 to further expand his career. Northrop left on good terms when he accepted a position as chief engineer with Lockheed Aircraft Company. Shortly after being hired, Northrop began to work on a new project, the Lockheed Vega. On July 4, 1927, the Vega test flight was such a massive success that it created an instant backlog of orders. Every pilot wanted a Vega, and many set new records that Lockheed advertised the slogan “It Takes a Lockheed to Beat a Lockheed.”

Lockheed Vega (courtesy

Even though Northrop was ecstatic with the Vega’s performance and worldwide acceptance, he knows the future of aviation lies within all-metal construction, making the wooden airframes obsolete. Northrop decides to leave Lockheed on June 28, 1928, to form the Avion Corporation, where he can work on new commercial aircraft designs using his new all-metal stressed-skin construction. He developed and built his first flying wing, the Avion Experimental No. 1, unveiling it in 1929. Northrop’s new “multi-spar” wing construction is revolutionary to future aircraft construction where multiple full-length span-wise stiffeners, or shear webs, replaced the traditional wing spars attached directly to the fuselage for structural support. I’ll cover a bit more on his multi-cellular wing construction in a few paragraphs, but let’s continue with the timeline.

Northrop “Experimental No. 1” Tractor (NX216H) (courtesy Northrop)

On January 1, 1930, Northrop sold his Avion Corporation to William Boeing’s company, the United Aircraft & Transport Corporation, establishing the Northrop Aircraft Corporation. Northrop then turned his attention to designing and building a new commercial aircraft, the low wing Alpha featuring his metal stressed skin technique. The highly polished aluminum skin gleamed in the sunlight, and Northrop was proud of his newly designed aircraft! He always felt that his most significant contribution to aviation technology was his new structural innovation, the stressed skin construction. Northrop often quoted, “As far as the structure is concerned, that which was developed into the Alpha was really the pioneer for every airplane in the sky today.

Northrop Alpha (courtesy

The Northrop Alpha is an all-metal six-passenger cabin low wing monoplane powered by a Pratt & Whitney Wasp radial engine rated at 425 hp. The pilot is seated slightly above the passenger cabin in an open cockpit located towards the aircraft’s aft section. The Alpha is the first commercial aircraft to use deicer boots on the leading edges, allowing day or night operations in all weather conditions combined with the state of the art radio navigation equipment. On April 20, 1931, TWA started their coast to coast service with the Alpha on a flight from San Francisco, California, to New York, New York, in just over 23 hours with 13 stops. The Alpha was a great success, and a total of 17 were built, with TWA operating 14 planes.

In September 1931, the Northrop Aircraft Corporation merged with Stearman Aircraft in Wichita, Kansas, due to the Great Depression’s collapsed economy to economize the company. Northrop isn’t happy with the merger and decides to form a new company, vowing not to leave California. He has three people agreeing to stay with him, Walter J. Cerny, Kenneth Jay, and Don Berlin, but he still requires the financial support of his good friend Donald Douglas.

DC-1 (courtesy

Douglas thought very highly of Northrop’s designs, especially his new “stressed skin construction,” which he thought would be perfect for the D.C. airliners. As a result of their conversations, the two men formed the Northrop Corporation based in Inglewood, California, as a Douglas subsidiary on January 1, 1932.

To help me better understand Northrop’s multi-cellular wing construction, I found a quote in the document 3-22(a-b) 3-22-b: Engineering Department, Douglas Aircraft Co. “Development of the Douglas Transport,” Technical Data Report SW-157A, ca. 1933-34, Folder AD-761184-05, Aircraft Technical Files, National Air & Space Museum, Washington, D.C., as stated;

Multi-cellular wing construction of the Northrup YB-35 in 1946 (courtesy Northrup)

In determining the wing construction of the early Douglas machines single, two, three and multi spar designs were considered as well as shell type and multi-cellular designs. After a thorough investigation of all types the Northrop multi-cellular wing construction was finally decided upon. This type of structure consists of a flat skin reinforced by numerous longitudinals and ribs. The bending is taken by the combination of flat skin and full length [longitudinal] stringers. Three main flat [vertical] sheets or ‘webs’ carry the shear loads. Torsion and indirect stress are carried by the skin with frequent ribs preserving the contour and dividing the structure up into a number of small rigid boxes or cells. Since the major loads are carried in the outer surface of the wing as well as in the in the internal structure, an inspection of the exterior gives a ready indication of the structural condition. The unit stresses in the material are low and therefore the deflections are at a minimum giving a maximum in rigidity. This construction has proven to be a happy medium of those considered since it combines practically all of the advantages of each; namely, very small unsupported areas, extreme lightness for its strength and rigidity; also ease of construction, inspection, maintenance and repair.

Donald Douglas (courtesy Douglas Aircraft Company)

Initially, the Northrop Corporation’s main focus was to serve as an experimental and research department for Douglas but soon began to produce aircraft when output capacities exceeded Douglas’s production limitations. Looking to fill the request of a fast cargo mail plane over long distances for the airlines and an aircraft capable of experimental over-weather or high altitude flights with deicing technology, Northrop designed and built the Gamma, an upgraded version of his successful Alpha aircraft. A 710 hp nine-cylinder Wright “Cyclone” radial engine, SR-1820-F3, provides the power for a cruising speed of 215 mph at 7000 ft with a service ceiling 20,000 ft. The pilot’s cockpit retains the original location, aft of the wing’s trailing edge, but features an enclosed sliding canopy that offers an unobstructed view of the 47′ 10″ cantilever wingspan. The front of the large round fuselage has two cargo bays with a total capacity of 1300 lbs, placing the entire payload weight over the center section of the wing. Gross weight is 7350 lbs with a range up to 1700 miles at 40 gallons per hour supplied by the 334-gallon fuel system. The fuselage has an overall length of 31′ 2″ and is 9′ in height.

Northrop Gamma 2B “Polar Star” in 1935 (source and author unknown)

Production started in 1932, and the first Gamma off the assemble line, the Northrop Gamma 2B Polar Star, went to Lincoln Ellsworth on November 29, 1932, to be shipped to the Ross Sea for the start of his 1934 Antarctica expedition. Northrop produces a total of 61 Gammas through 1937, with 49 sold to the Chinese.

Northrop Gamma 2A “Texaco Sky Chief” in July 1933 (courtesy Elwood W. Mason)

Frank Hawks of the Texas Oil Company purchased the second Gamma, a Northrop Gamma 2A Texaco Sky Chief, and set a record flight on June 2, 1933, from Los Angeles, California to New York, New York in 13 hours, 26 minutes, and 15 seconds.

Northrop Gamma 2-D (courtesy Patrick Rodwell)

TWA received their Gamma 2-D for the transport of mail and cargo, and on May 13, 1934, Jack Frye set a new cross-country record for transport planes leaving Los Angeles, California, and arriving in Newark, New Jersey in 11 hours and 31 minutes.

Northrop Delta Type 1A (courtesy SDASM Archives)

While in the middle of the Gammas production, Northrop added the newly designed Delta passenger transport to the assembly line to start production in 1933 at the new plant in El Segundo, California. The prototype, Type 1A, successfully flew in May of the same year, and Northrop received an order from TWA for 15 planes. Taken from the proven and popular Gamma design, the Delta retains the same airframe and powerplant but relocates the cockpit to the airplane’s front. The widened semi-monocoque fuselage can accommodate up to eight passengers, plus the pilot seated slightly above the passenger level in an enclosed cockpit. An optional configuration of two pilots with six passengers and cargo arrangements are also available. The Delta Type 1A receives certification to carry six passengers after a few months of testing. On a lease, TWA receives delivery on August 4, 1933, for preliminary trails to transport mail between Los Angeles, California, and Kansas City, Missouri. Unfortunately, on November 10, 1933, the plane develops an engine fire in flight near Albuquerque, New Mexico causing the pilot Harlan Hull to eject from the aircraft. He survives by parachuting safely to the ground, but the airplane is a total loss. TWA decides to cancel its order due to the recent flight problems and a rumored amendment to the Air Commerce Act of 1926 taking effect in October 1934, banning the Delta from being operated by U.S. airlines. More on that later.

Northrop Delta Type 1B (source and author unknown)

The second Delta, Type 1B, is purchased by the Mexican subsidiary Aerovias of Pan American Airways in August 1933 for the Los Angeles-Mexico City flight route. In May 1934, another engine fire destroyed this second Delta, but fortunately, no one is injured. I looked into the possibility of a common issue with the engine, but the Type 1B used a different powerplant, a 660 hp Pratt & Whitney Hornet T2D-1 engine, so that doesn’t seem to be a common cause. Unless there was some defect in the fuel delivery system, I’m not an A&P mechanic, and your guess is as good as mine. Some articles state that the aircraft crashed due to an engine fire while in service on a flight to Mexico City, but I cannot confirm this statement. Most accident reports say there was an engine fire without any injuries, but it’s unclear if it was on the ground or in flight.

Northrop Delta Type 1C (courtesy

The last Delta to be sold to an airline is the Type 1C and was purchased by AB Aerotransport in Sweden in April 1934, and given the name “Halland.” Only one of the Type 1C model is built and featured the optional Pratt & Whitney T1D-1 engine rated at 700 hp. This aircraft had a long service life without mechanical issues, as the previous models, operating on the Gothenburg-Copenhagen-Malmo and Malmo-Copenhagen-Hanover flight routes. “Halland” ceased its airline service in May 1937 and was later purchased by a private citizen.

These first three Delta models had a single-seat cockpit with a sliding canopy and operated with a two-bladed propeller. Later, the new Delta models switched to a three-bladed propeller and reconfigured the cockpit to allow room for a pilot and co-pilot. Northrop produces 32 Deltas, but the majority are sold outside the U.S. or to the private market.

The initial plan to sell the Deltas as single-engine airliners capable of carrying medium loads on the U.S. trunk airline routes came to an abrupt halt when an amendment to the Air Commerce Act of 1926 regarding airline safety requirements take effect on October 1, 1934. The revision requires all airlines operating on the trunk routes to use multi-engine aircraft at night or over rough terrain, instantly banning the Delta from any airline.

The new provisions included the requirement for airline pilots to use multi-engine aircraft capable of operating with one engine not functioning when flying at night or over terrain not readily permitting emergency landings. Instrument or blind flying was permitted only for multi-engine airliners equipped with two-way radio.

Canadian Vickers Northrop Delta (courtesy RCAF)

Northrop, discouraged with the new amendment, turns his attention to the mounting military aircraft contracts and finds the short-lived Delta project a much-needed break from the nuisance that the Delta was creating. He did continue to produce the Delta 1-D, already in the assembly line before the new amendment, but reconfigured the cabin for the limited private sector sales and selling the remaining inventory to other countries unaffected by the amendment. In August 1936, Canadian Vickers Ltd purchased the last Delta produced by Northrop as part of assembled patterns and built 19 additional aircraft under license in their factory until October 1940. Canada initially selected the Delta as a photographic survey aircraft. Still, in August 1939, with the approaching Second World War, the Deltas are converted to coastal patrol planes fitted with floats to carry out long anti-submarine missions. After only two months of use, the ocean environment proved to be too damaging to the Deltas from the large ocean swells and corrosion caused by the salty water, the military quickly returned them to land use.

Northrop Delta 1-D “The Richfield Eagle” (courtesy SDASM Archives)

Now on to the private market. Northrop offered the optional “Executive Model” for the Delta 1-D, which included custom seating for 5 to 7 people and focused the advertising towards professional sports athletes and businessmen. A Wright “Cyclone” radial engine, SR-1820-F2, produced 735 hp at 2100 rpm at 4000 ft giving the Delta 1-D similar performance as the Gamma perfect for long country flights. The maximum speed is 219 mph at 6300 ft with a cruising speed of 200 mph at 8000 ft at 3/4 throttle. Six fuel tanks located in the center section of the wing carry a total fuel capacity of 328 gallons providing a range between 1100 and 1500 nautical miles at 3/4 throttle depending on the headwind or tailwind. The climb rate is 1200 ft/min at sea level with a service ceiling of 20,000 ft. Northrop offered a Wright SR-1820-F52 engine as an option rated at 775 hp at 2100 rpm at 5800 ft for those interested in a little more performance. Now that should get your blood pumping!

Northrop Delta 1-D (courtesy Jacob Zilber)

A spacious cabin measuring 58 inches wide is heavily sound-proof with a left side entry door and customizable in either the “Club” or “Executive” packages. Both versions are incredibly lavish, featuring overstuffed chairs, a divan with storage underneath, a bathroom, and a 25 cubic foot baggage compartment behind the tail section’s cabin. The “Club” upgrade reduced the seating for 4 or 5 people. It included a refined interior, some upholstered in red and tan leather, a complete lavatory, a Sperry autopilot, and extra instruments. Standard equipment for either package includes; a Hamilton-Standard controllable propeller, an electric starter, a generator, an Exide battery, an oil-cooling radiator, navigational lights, landing lights, parachute flares, a fire extinguisher, a Western Electric radio, window curtains, and a full set of airline-type instruments. The base price started at USD 37,500 with standard equipment in 1934, which roughly equates to USD 727,500 in this writing, 2020.

Some of the “Delta Executive” owners include; Powell Crosley Jr., Hal Roach, Richfield Oil, Stewart Pulitzer, Earl P. Haliburton, and Wilbur May, to name a few. I recognize Powell Crosley Jr. for his invention and manufacturing of the 1921 Crosley Harko tubless crystal radio and Hal Roach, Laurel and Hardy’s comedy producer. These are extraordinary men, including Jack Northrop, and these talented individuals’ success always inspires me.

Tony’s Scrapbook; Jean Mermoz

I’m finding that with each new clipping that I discover in my father’s scrapbook opens a historical path that I never knew existed. It’s not as simple as I first thought when I was looking through his book for the first time. Don’t get me wrong, I did appreciate the wealth of historical facts, but was too naïve to understand the importance of the information contained within these pages. My mindset has changed since I wrote the first blog on Vincent Burnelli and continues to evolve with each passing article. The story of Jean Mermoz is no different, and please join me while I interpret the facts and create a timeline of this alluring pioneer! And I thank my father for introducing me to these people, the historical aviators of the past for which aviation today wouldn’t exist if it wasn’t for their significant contributions.

A Couzinet 70 Arc-en-Ciel III, aka “Rainbow,” shown taking off in the above news clipping dated by my father, January 1933, provided by Times Wide World Photos, Paris Bureau. I didn’t recognize the French word “Arc-en-Ciel” in the description and found the title a little confusing regarding a rainbow. I thought, how strange to mention a “Rainbow” in a black and white photo. But soon enough, and with a little research, I realized the English translation for “Arc-en-Ciel” is “Rainbow” and was then able to identify the aircraft correctly. And to think, the clue was in the title all along. Now, let us return to the article, shall we?

Couzinet 70 (courtesy Pinterest, Unknown Author, Unknown Source)

Mermoz pilots the trimotor Couzinet 70 landplane from Istres, France to Buenos Aires, Argentina, with a return flight back setting a new world record in the flying time of 54 hours and 33 minutes. This monoplane’s sleek design was ahead of its time, giving France an edge over other rivals. Plus, it demonstrated the reliability needed in making regular transatlantic airmail service possible and is Mermoz’s favorite for long overwater flights.

This simple news clipping that my father saved contains a bountiful wealth of aviation history that I find troublesome as to where to continue. I thought about focusing on the aircraft, the Couzinet 70, and the designer Rene Couzinet behind this beautiful machine, but I strongly feel that I need to explore the life of Jean Mermoz. He is an extraordinary individual, and I’m excited to share what I’ve learned about this fascinating man! So, find a comfortable chair, get settled in, and join me on this marvelous journey.

“Breakdown in the desert 200km from Cisneros” (courtesy
Jean Mermoz (courtesy

Recognized as a national hero and often referred to as the “French Lindbergh,” Jean Mermoz was born on December 9, 1901, in Aubenton, Northern France. He was very reserved as a child and was mostly interested in literature or writing poems. No one would ever assume that he would be interested in becoming a pilot, but that all changed when he enlisted into the French Army in 1920 at age 18. His fascination with the pilots and aircraft of World War I led to his desire to become one himself, and in 1921 he received his pilot’s license. After training in France, he is posted overseas to Syria later that year. By the end of 1922, he has flown over 600 hours in 18 months and noted for surviving a plane crash in the North African Desert. He spent four days in the desert before rescuing, where his keen survival skills kept him alive. The next two years are hard for him, and with each passing month, military life finally becomes intolerable. In March 1924, the military demobilized him from the Army as a decorated pilot. He sets his sights on becoming a pilot for a private aviation company, but things didn’t as smoothly as he planned.

Finding himself out of work in Paris with little money to his name without any responses from his resume, he has no choice but to take odd jobs and rely upon soup kitchens for food. But through his perseverance and strong will, and maybe a bit of luck if you believe in such, he finally receives a letter of interest. It is from Didier Daurat, the Director of Operations at Lignes Aeriennes Latecoere (Latecoere Airlines), requesting an interview. The interview went well, but the first flight test didn’t go as well as he hoped to impress his potential new boss. Mermoz is 23 at this time, is a decorated military pilot, and has enough self-esteem for a room full of pilots, which led to quite the aerial display of his aerobatic skills. Daurat is not impressed and quoted, saying, ” I don’t need circus artists, just bus drivers.” But his passion for aviation did impress Daurat and is offered the job. A turning point in Mermez’s life that he desperately needed where he once referred to in his own words, “his life as an outcast ends.”

Breguet 14 (courtesy

In 1925, Mermoz pilots World War I surplus Breguet 14 biplanes on the first Latecoere Airmail routes connecting Toulouse, France to Barcelona, Spain, Casablanca, Morocco, and Dakar, Senegal. These World War I surplus biplanes are purchased by Latecoere and fitted with podded containers mounted under each side’s lower wing to carry the mail bags. The Breguet 14 is mostly reliable, and Mermoz is honored for flying 120,000 kilometers (75,000 miles) and 800 hours of flight time logged in a single year. But in 1926, Mermoz develops engine trouble while en route with mail delivery from Casablanca to Dakar and makes an emergency landing in the Mauritanian Desert. A group of Nomadic Moors capture him and hold him prisoner until a paid ransom is received. Again, luck seems to be on Mr. Mermoz’s side or is incredibly skillful at taking control of the current situation. Most airmen forced down by mechanical failure are executed, but he survives captivity after a few days and is released when the ransom money is received. During this time, it is a common hazard of the job and a hazard that I wouldn’t like ever to experience, nor would I want anyone else to.

Latecoere 25 (Late 25) (courtesy Jacques Moulin)

In 1927, Latecoere Airlines started replacing the Breguet 14 biplane with its design, the more reliable Latecoere 25 monoplane (Late 25), and changed its name to Compagnie Generale Aeropostale, aka Aeropostale. Mermoz switched to the South America route and moved to Buenos Aires, Argentina. There he would set up airmail service for Aeropostale between Rio de Janeiro and Buenos Aires. After accumulating flight time in the new Late 25, Mermoz pilots the first successful air crossing with a seaplane of 3,000 kilometers from Dakar, Senegal, to Natal, Brazil, in 1928. He completes the first South America night flight from Natal to Buenos Aires in the same year. The land route was challenging terrain and unmarked by any lighted beacon, but a few bonfires did help with navigation along the flight path. This successful night flight alleviated the limiting daylight only operations and had proven that airmail service could continue safely at night.

The Railways of South America (courtesy

On September 18, 1928, he made his first attempt to shorten the Argentina-Chile route by establishing a flight path over the Andes Cordillera that would eliminate the 1600 kilometer detour typically flown to avoid the mountain range. Mermoz and his mechanic Alexandre Collenot set out to explore the terrain from Buenos Aires and establish a flight path over the Andes suitable for future postal lines within the operational ceiling limitations of their Late 25 of 4500m. On this first crossing, he decides to follow the Trans-Andean railway route to interpret the landscape and completes the flight over the Andes without any problems. He returned three days later, following the same course, and landed victorious in Buenos Aires on September 21. Once again, Mermoz proves his capabilities through his relentless determination and is ambitious for future challenges!

In a matter of no time, a new mission presented itself on February 28, 1929. Mermoz is assigned to fly his Late 25, accompanied by Collenot from Buenos Aires to San Antonio Oeste to charter the International Aeronautical Federation’s cofounder, Henry de La Vaulx, to Santiago. From there, Mermoz pilots the plane to Plaza Huincul, Neuquen, for a short layover, and then to cross the Andes on a new flight path farther South near the city of Concepcion. While en route, he develops engine failure due to a carburetor issue and has no choice but to make a forced landing on a narrow platform with a sheer drop off at 2800m. Not an easy task for the most skilled pilots and unattainable for most, Mermoz proves his exceptional ingenuity to stop the plane before falling into the ravine. He and Collenot make the needed repairs, probably a carburetor icing issue, and in an hour later, land safely in Santiago.

Not satisfied with the route he had just taken, Mermoz decides to explore for new flight paths further North for a return trip back to Buenos Aires. On March 6, 1929, he and Collenot flew several hundred kilometers, scouting the terrain and plotting potential passages over the Andes. After a few hours in the air and their field book full of notes, both men land safely in Copiapo. Unsatisfied with the previous day’s expedition, Mermoz and Collenot set out on March 9 to continue to locate a direct air route between the passes of Come Caballos and San Francisco, Argentina. They take off from the Chamonate aerodrome in Copiapo and start searching for unrestricted access through the Andes. The flying is difficult and seems almost impossible at times, but through his unmitigated determination, Mermoz spots a free passage rising to 4500m located on the side of Cerro Copiapo. He realizes the ceiling limitation of his Late 25, and the plane struggles to exceed 4200m. Still, in true Mermoz fashion and quick thinking, he takes advantage of the updrafts near the mountain walls and manages to climb to the necessary altitude. He thought he made it for an instant, but the turbulent winds pushed his exasperated plane towards the other side of the slope in a matter of seconds. With the engine at full throttle, but powerless against the wind’s velocity, Mermoz knows he is out of choices and immediately needs to land if they are to survive. He throttles back on the engine and chooses the best location for a hard landing on an unfavorable snow-covered area with an altitude of 4000m. The airplane is severely damaged, and Mermoz knows they need to make the necessary repairs for any chance of getting off this plateau alive. A quote from a letter Jean Mermoz wrote to Vova de Martinoff dated April 1929 describes this disastrous event.

Three days and two nights at 4000 m altitude, 16 to 26 degrees below zero, starving (my mechanic having forgotten the reserve food), repairing our landing gear very slightly sagged on one side and our tail unit a little torn off on a ledge of rocks. Water pipes burst from the cold. Repairs made with chatterton, canvas tape and enamel. Take off after 3 km of jumps over three ravines. Ceiling of the device maximum 4500 m. Full engine speed 1580 turns or 330 HP. I had spotted in advance the places where I had to touch the wheels to make the planned leaps. Everything went well and 1 hour 40 minutes later I landed at Copiapó, my starting point. Three days later, I left for Santiago then, crossing the Cordillera, I brought the aircraft back to its starting point …” 

He and Collenot landed at Copiapo on March 12, around noon in his Late 25 in deplorable condition. Both men were almost unrecognizable, weakened by both the cold and hunger, but still managed to stay conscious for the hour-plus flight back to the Chamonate aerodrome. “It’s a miracle,” one airman shouts out when he can’t believe what he sees. Do my eyes deceive me, he thought? The other airmen rush over to see for themselves. It’s true, they’re alive, and to survive for three days without a trace is a real miracle because they all know it’s almost impossible for anyone to return from the Cordillera after missing for so long. The Chilean Army sent a team to investigate the crash site and to confirm this unbelievable feat. They returned with some of the aircraft’s debris at the location Mermoz told them about, and the myth of the “Archangel” is born!

Aeropostale receives news that Mermoz and Collenot have returned safely to Copiapo, but in a badly damaged Late 25 that proves to be incapable of flights over the Andes Cordillera. The company immediately acquires five Potez 25s for the newly plotted Buenos Aires-Santiago Line to replace the inadequate Late 25. The Potez 25 is a biplane built initially for observation and bombing purposes but quickly found useful in civil aviation due to its high ceiling altitude of 7200m. It has a range of 1260m with a payload of 500kg perfect for the new air routes.

Potez 25 (courtesy

After recovering from his accident, Mermoz accumulates flight time in the Potez 25 with multiple crossing for Aeropostal. He invites Henri Guillaumet, a friend he met previously in the military, to accompany him on July 14 and 18 to take over the Cordillera’s new flight path establishing the Buenos Aires-Santiago Line. Mermoz sets his sights on future quests across the South Atlantic. At the same time, Guillaumet continues to fly this dangerous route for 393 flights, including a similar accident as Mermoz on June 13, 1930, on his 22nd crossing.

Latecoere 28-3 F-AJNQ (courtesy

On May 12, 1930, a Late 28-3, F-AJNQ, named “Comte de la Vaulx” in honor of French aeronaut Henry de la Vaulx and fitted with pontoons established the first postal link across the South Atlantic piloted by no other than Jean Mermoz. A fully loaded seaplane with 122 kilograms (269 pounds) of mail and enough fuel for a 30-hour flight leaves Saint-Louis, Senegal, en route to Natal, Brazil. Guiding Mermoz on this historic flight is his co-pilot and navigator Jean Dabry, and radio navigator Leopold Martial Emile Gimie. They fly southwest across the South Atlantic ocean with a planned flight path of about 3100 kilometers. The flight crew completes this mission in 19 hours, 35 minutes, as reported by the US Centennial of Flight Commission, and becomes the first non-stop flight to cross the South Atlantic! Previously, boats were the only option for mail delivery between France and South America, taking an average of 5 to 6 days, but this commemorated flight significantly shortened that delivery time.

From left to right: Mermoz, Gimie, and Dabry (courtesy Musee Air France)

Mermoz and his crewmates became national heroes, in their home towns and Argentina, and set a new hydroplane record for flying the longest distance in a straight line. His very close friend and fellow Aeropostal pilot, Antoine de Saint-Exupery, is quoted saying, “Pioneering thus, Mermoz had cleared the desert, the mountains, the night, and the sea.”

After the much-deserved celebrations and waiting for enough new mail to fully load the seaplane, the three crewmembers depart Natal on June 8 for a return flight to Senegal. After 14 hours into the flight, the engine develops an oil leak, and Mermoz decides to make a forced landing in the ocean near a dispatch boat named “Phocee” about 900 kilometers from their destination. With the mail safely transferred to the ship, they try to tow the seaplane behind the ship. The aircraft is eventually lost at sea when it becomes too difficult for the boat to pull.

In 1933, the formation of Air France began from the nationalizing of Aeropostale and four other airlines due to economic and political troubles along with the continuing worldwide depression. During this transition and distancing himself from any controversy, Mermoz starts a series of long-distance flight known as “Raids” by the French.

We have come full circle to my inspiration for this post’s title and a time when my father first saw that news clipping of Jean Mermoz in his Couzinet 70 Arc-en-Ciel during one of his “Raids.” I won’t trouble you by recapping the details of this event that I’ve already covered at the beginning of this post, and I thank you for your commitment so far. I find Jean Mermoz awe-inspiring and understand why he made it into my father’s scrapbook, so let’s continue.

After completing his short series of “Raids,” in 1933, Mermoz moves to Buenos Aires with his close friend Saint-Exupery to help set up new flight lines for the newly developing Aeroposta Argentina, later to become Aerolineas Argentina. The two men go on to be considered the essential people in the foundation of Argentine Commercial Aviation history. Mermoz is also appointed as General Inspector by Air France in the same year. During 1934 and through 1936, Mermoz pilots private expeditions using Latecoere 300 seaplanes and completes over 20 voyages.

Latecoere 300 Croix-du-Sud (courtesy

The Late 300 seaplane’s sole design was to transport mail on the South Atlantic line between Dakar, Senegal, and Natal, Brazil, for Aeropostale in 1931. The first flight went well, but it sank shortly after in the Etang de Berre in December due to a centering issue. At the beginning of 1932, Latecoere rebuilds the aircraft and names it “Croix-du-Sud” or Southern Cross and is operational in October. The seaplane, or more commonly known as the “flying-boat,” is a monoplane design featuring a parasol-wing with four 650 hp Hispano-Suiza 12NBr water-cooled engines mounted in tandem pairs. The sheer size is impressive with a 44.20m wingspan, a length of 25.86m, a height of 6.50m, and a gross weight of 23,000 kilograms. The ceiling altitude is 4,600m, with a cruising speed of 210km/h at 4,450 kilometers. On December 31, 1933, pilot Jean Bonnot sets an international record in the “Croix-du-Sud” for covering a 3679km non-stop flight in just over 23 hours in Senegal.

Late 300 (courtesy

On the early morning of December 7, 1936, Jean Mermoz takes off from Dakar piloting the Late 300 “Croix-du-Sud” soon to be his 24th crossing of the South Atlantic. The aircraft proudly displays the new Air France colors, and Mermoz feels comfortable knowing that his friend Henri Guillaumet is overseeing the operation as base chief. Five flight crewmembers onboard this flight include the pilot Mermoz, the co-pilot Alexandre Pichodou, the flight engineer Jean Lavidalie, the navigator Henri Ezan, and the radio operator Edgar Cruveilher.

Things didn’t go as smoothly as Mermoz hoped, and he immediately returned to the hydro base with engine trouble around 6 am. Mermoz radioed in “one of the variable-pitch propellers is not going fast,” and would like to switch to a different plane after having the mail transferred to land. Guillaumet informs him that no other aircraft is available, and his only option is to make the necessary repairs to the “Croix-du-Sud.” Knowing the importance of the mail delivery schedule, Mermoz decides on a quick repair to get back into the air as quickly as possible. The repairs don’t take long, and as he boards the plane, he says, “quick, let’s not waste time anymore.” The aircraft departs just before 7 am and things seem to be ok for the moment. Around 10 am later that morning; the Dakar base receives a radio message that everything is fine.

In an unforeseeable event, the base receives a brief radio transmission from Mermoz at 10:47 am, “Right rear engine cut,” then cuts out abruptly. A search and rescue mission leaves immediately, but are unsuccessful in locating the aircraft or crewmembers. The most logical assumption is that the right rear engine’s reducer ruptured, causing the propeller’s release from its axis. The result would have badly damaged the fuselage rendering the flight controls unresponsive or completely severing the tail section. Either situation is an inevitable catastrophic failure.

Tony’s Scrapbook; Pitcairn PA-19 Autogyro

A worn thick cardboard cover lies loosely on top of an aged book filled with new house designs of the 1930s now covered with newspaper clippings and articles. The binding and back cover are missing, with the pages discolored and worn over time from a young man’s fascination with aviation and repeated viewing of his precious collection. As I carefully turn each page, I often find myself thinking of a time when he was adding to his scrapbook and how these events shaped a man to become a pioneer himself, bringing aviation to the Niagara Frontier in the 1940s and a test pilot of the P-47 Thunderbolt. I find his collection so fascinating that I never know where to start, and I wish I possess a prolific writer’s skills. But until then, I’ll start at the beginning and take it page by page without any chronographic order. I hope you enjoy this series, Tony’s Scrapbook, and please sign up for email notifications for future blog posts if you find them interesting.

A page from Tony’s Scrapbook

A newspaper clipping from the Herald-Tribune that my father dated March 1933 of a Pitcairn PA-19 autogyro craft hovering over midtown New York. This new design features the first passenger cabin that could comfortably carry four people, including the pilot. The PA-19 is the largest cabin autogiro ever constructed in the US at the time with a sizeable stabilizing rotor or “Windmill” mounted on top of the cabin over 50 feet in diameter. The wingspan is 38’8″, and the fuselage has a length of 25’9″ with dual rudders. A nine-cylinder air-cooled Wright R-975E-2 Whirlwind radial engine provides power to the propeller rated at 420 hp. This engine is the largest of the Whirlwind models with a displacement of around 975 cubic inches or just under 16 liters.

“Detroit News” Cierva PCA-2 (courtesy Melissa D. Scripps)

What is an autogyro or often spelled autogiro, you ask? Well, you’re not alone, and I too needed to research this unique design that emphasizes safer flights at slow speeds and short take-off and landing (STOL) capabilities. An autogyro is a rotary-wing aircraft equipped with fully articulating, or hinged, airfoil-shaped rotor blades suspended above the fuselage attached to a central hub mounted on a freely spinning vertical axle shaft. The key here is freely spinning rotor, and please don’t confuse an autogyro with a helicopter, because a helicopter uses a powered rotor.

Cierva C.4 (courtesy Heli Start)

During forward motion, each blade’s independent movement reduces the uneven lift created between the advancing blade and the retreating blade, known as “Dissymmetry of Lift.” Without getting too deep on this subject, for my sanity and yours, let’s remember that the vital fact here is the invention of fully articulating rotor blades by Juan de la Cierva with two others’ help in 1922. Emilio Herrera, a military engineer, and Rey Pastor, a mathematician, provided the technical knowledge he desperately needed to solve this problem on earlier prototypes. The C.4, De la Cierva’s fourth prototype, carried out the world’s first successful flight of a stable rotary-wing craft or, as he called it, an Auto-Spin at the end of January in 1923.

A propeller is needed for the forward motion to generate lift by the unpowered, freely rotating rotor blades that will continue to spin during flight. Mechanical assistance is required to start the rotor blades’ rotation before take-off and usually provided by a PTO off of the engine or by hand with a rope wrapped around the axle shaft in earlier designs. So forget about taking off or landing anywhere there wasn’t anyone to help “pull start” your rotor in those first models.

Cierva C.6 (courtesy Sci Hi Blog)

I can only hear it now. “Hey, Bob!” What he exclaimed! “Can you start my rotor on my new autogiro that I just built by pulling on this long rope? Oh, and watch your head.” You want me to do WHAT he yelled back. I’m sure they went through a lot of leather gloves back then.

Pitcairn PA-5 Mailwing (courtesy Jim Hough)

Harold Frederick Pitcairn, son of the Pittsburgh Plate Glass Company (PPG) founder John Pitcairn Jr., started an aviation business, Pitcairn Air Service, at a small flying field in Bryn Athyn, Pennsylvania, in 1924. There he offered flight lessons, scenic rides and housed a fleet of eight aircraft, including his first aircraft purchased in 1923, a Farman Sport biplane. He later went on to create Pitcairn Air Field (#2) in 1926 when he bought 190 acres in Willow Grove, Pennsylvania, to expand his business. Since graduating from flight school in 1918, Harold Pitcairn and his close friend from school Agnew E. Larsen developed many ideas for vertical lift and rotary-wing aircraft, and the two are issued 270 patents. Seeing an opportunity to acquire a contract with the US government for quick, reliable airmail delivery for the New York to Atlanta route, Mr. Pitcairn designs and builds the Pitcairn PA-5 Mailwing biplane in 1927 with the help of Mr. Larsen. The PA-5 Mailwing can carry 600 pounds of mail with a cruising speed of 120 mph, making it the ideal aircraft for this contract. After winning the New York-Atlanta contract, Mr. Pitcairn bids on and wins the Atlanta-Miami contract and now services most of the East Coast for daily airmail delivery. The PA-5 was so popular that he sold custom versions to celebrities like Howard Hughes with a chrome-plated engine and one to Felix du Pont with gold-plated rocker covers.

Cierva C.8 photo from Le Document aéronautique December,1928

Even with the success of the PA-5 and his Flight Service business, Mr. Pitcairn believes that the future of aviation lies within the autogyro, and he purchases a Cierva C.8 Autogiro in 1928 after a test flight in England. He is so determined to design and build his versions of autogyros using Juan De La Cierva’s designs, that he decides a significant change in his business structure is necessary. His plan is simple, but not for the weak-hearted. Sell his current business, form a new one to sell autogiros in the US, and start working on improving the technology to make them the country’s safest aircraft. Since he has committed himself to follow through with his dream of the rotary-wing vertical lift aircraft, he forms a partnership with Juan de la Cierva. Mr. Pitcairn creates the Pitcairn-Cierva Autogyro Company of America in 1929, where he is licensed to build and sell autogyros in the US under the De la Cierva patents. With the sale of his enormously successful airmail line and Pitcairn Air Lines to Curtiss Wright and General Motors’ syndicate for 2.5 million in July, he and his design team can focus all of their attention on building autogyros to be sold under this new licensing agreement. The transition from fixed-winged aircraft to autogyros came quickly for Mr. Pitcairn, and he started working on new designs immediately after he reassembled the Cierva C-8 that he purchased in England in 1928 after being shipped to Pitcairn Field, Pennsylvania. There, Mr. Pitcairn received flight training in his newly reassembled C-8 from Cierva pilot Arthur “Dizzy” Rawson in December of that same year. Harold Pitcairn becomes the first rotary-wing pilot on the North American Continent with the autogiro’s introduction in the winter of 1928.

Harold Pitcairn May 14, 1929 (photo courtesy Corbis-Bettmann)

Harold Pitcairn successfully piloted his autogiro, nicknamed the “Windmill” from Pennsylvania to Washington DC on May 14, 1929. His first long trip proves that his radically new design is airworthy for such an extended flight in aviation history. In 1930 Mr. Pitcairn created a subsidiary, the Autogiro Company of America as a patent licensee to Buhl, Sikorsky, Kellett, and other interested manufactures. In the same year, Harold F. Pitcairn and associates receive the prestigious Collier Trophy “for development and application of the autogyro and its demonstration as safe aerial transport.” 1930 is a busy year for Mr. Pitcairn, and he introduces the Cierva PCA-1 as the first commercial autogyro in the US. It is a redesigned version of the C-8, but with the fuselage of the PA-5 Sport Mailwing. Shortly after, the Cierva CPA-2 is released the following year with significant improvements and is quite substantial in setting world altitude records and a cross-country flight by Amelia Earhart. It also earns government approval for the first non-conventional aircraft. The CPA-2 is today’s modern helicopter’s ancestor and initialized the groundwork for the powered rotor blade.

Amelia Earhart and her PCA-2 (courtesy Purdue University)

On April 8, 1931, Amelia Earhart set a world altitude record of 18,415 feet in a Pitcairn PCA-2 autogyro at Pitcairn Field. She held that record for over a year until Lewis Yancy piloted a PCA-2 on September 25, 1932, setting a new world altitude record of 21,500 feet.

James G. Ray, the chief pilot for Pitcairn, lands a PCA-2 autogiro on the south lawn of the White House on April 22, 1931, before President Hoover and leading aviation authorities in Harold Pitcairn’s acceptance of the Collier Trophy for the development of the autogiro.

Noorduyn Norseman (courtesy B. Nord)

Even though Harold Pitcairn built the PA-19, Robert B.C. Noorduyn is responsible for designing the first enclosed four-seater autogiro while working as a designer at the Pitcairn-Cierva Autogyro Company in 1932. If his name sounds familiar, he is best known for the legendary Canadian Noorduyn Norseman bush plane built in the 1930s.

Juan de la Cierva lost his life at the age of 41 when a plane he was on crashed after take-off on December 9, 1936. He boarded a Dutch DC-2 of a KLM airliner at Croydon Airfield bound for Amsterdam. The flight later departs around 10:30 am after being delayed earlier by heavy fog. During take-off, the DC-2 veered off the white guidelines on the grass runway and crashed into the roof of a building towards the end of the runway. Only 2 of the 17 passengers on board survive and is the single worst accident in British history at that time.

Harold Pitcairn and his team built many more autogyros variations up to 1943, with the PA-44 being the last model, but never delivered due to cooling issues. His company changed names two more times, to Pitcairn-Larsen Autogiro Company Incorporated in February 1941 and finally to AGA Aviation Corporation in December of the same year. The US Navy purchased Pitcairn Field in 1942, expanded it, and renamed the site United States Naval Air Station Willow Grove. The G&A Division of the Firestone Rubber Company acquired AGA Aviation Corporation in 1946 and, renamed to the Firestone Aircraft Company in 1947. As momentum gained on the new helicopter’s popularity, the autogyro lost interest, and by 1946, most manufacturers are producing helicopters under contracts for the US government. With the beloved autogyro’s enthusiasm fading, Harold Pitcairn decided to dissolve the Pitcairn Autogiro Company in 1948. Dealing with the loss of his company and seeing his patents used by other manufacturers and the government without compensation, Mr. Pitcairn hires legal counsel to pursue litigation for the illegal use of his registered patents starting in 1951. I can only imagine how frustrating this must have been for him. A man, an inventor who designed the Pitcairn Mailwing for reliable airmail service on the East Coast, flown through Pitcairn Aviation, later becoming Eastern Airlines after the sale. A pioneer who developed the autogiro and patents that resulted in the modern helicopter, and to see his designs used illegally without compensation must have been infuriating and agonizing. Harold Pitcairn would never know the victory he so rightfully deserved, and on April 23, 1960, he took his own life at the age of 62. Litigation continued after his death. In 1977 the US Supreme Court ruled in favor of Mr. Pitcairn of the infringement that the Autogiro Company’s rotor-wing patents legally owned and awarded his estate $32 million for lost compensation.

Tony’s Scrapbook; Burnelli CB-16

Tony had many scrapbooks, but his favorite is the one he started around 1930 using his father’s hardcover book “The Home” that he glued newspaper and magazine articles into that he found meaningful about aviation. Little did he know, or maybe he did, that he was preserving aviation history so the stories would always be shared and never forgotten! Before my father covered these pages with articles, this book outlined many home plans that you could browse with full descriptions and basic floor plans detailing the layouts. Towards the back, there is an order form to purchase complete plans and specifications for any of the model homes illustrated in this book. The price range is between $5 and $40 and includes an estimate of cost and materials list. I understand that my father’s parents didn’t have a lot of money during his childhood. They immigrated to Jamestown, New York, from Italy in the spring of 1920 when he was eight years old. He learned to utilize anything available by re purposing or upcycling, and this scrapbook is just one example he used throughout his life. He did this with aircraft hangers too, but I’ll save those stories for another time. The back cover is missing with some pages torn and discolored, but it’s in reasonably good condition for being around ninety years old!

I’ve been going through my father’s scrapbook and found a loose page that he saved from one of his “The AOPA Pilot” magazines. At first, I thought he kept it for the advertising for the new Narco Mark VI 190 channel crystal controlled VOR/LOC. I didn’t find a date, but it is page 105 and 106 from that unknown issue. When flipping this page over, I realized it was an article about Vincent Burnelli and his revolutionary CB-16 multiengine plane. Granted, it is only part of the article, but there is enough information about his CB-16 that I find him extraordinarily fascinating and yearning for more! I hope you enjoy this story as much as I did while researching and writing about this revolutionary aeronautical engineer, Vincent J. Burnelli.

Vincent Burnelli designed and built his first successful airplane, the Burnelli-Carisi Biplane, with his friend John Carisi at Maspeth, a borough of Queens in New York, in 1915 under the Burnelli Aircraft Company. The above photo shows the open cockpit “pusher” biplane at Hempstead Plains Aviation Field located east-southeast of Mineola, Long Island, New York. This field was renamed Roosevelt Field in 1919 in honor of President Roosevelt’s son, Quentin, who died during air combat in World War I. It didn’t take long for the two men to make money with their new biplane, and it was a great way to fund future projects. “We used it for barnstorming,” Mr. Burnelli explained. “You could make $500 to $1,000 in those days working a fair, and that was big money.” Vincent designed a night fighter a few years later with hopes of using it as a combat plane in World War I, but things didn’t work out, and he eventually sold the airplane to the New York Police Department for their aerial operation.

Lawson Airliner, 1919 (photo courtesy George Hardie)

At the end of World War I, Alfred Lawson, founder of the Lawson Aircraft Company, hired Vincent Burnelli as an aeronautical engineer and six engineering specialists to work on a new project idea of a sizable commercial aircraft to transport passengers regularly between major cities. Work began in March 1919, and within five months, the team built the first multi-engine passenger aircraft ever produced in the United States, the Lawson C-2 biplane “House on Wings.” This large aircraft features a 91-foot wingspan, is 48 feet long with a gross weight of 12,000 pounds. Powered by two 400-hp 12-cylinder Liberty engines mounted between the wings on each side of the fuselage developed a cruising speed of 110 mph with a range of more than 400 miles. Landing on two tandem wheeled landing gears mounted to the bottom wing inline with lower engine bracing gave maximum support, and a large tail skid supported the rear. Laminated wood bulkheads replaced the traditional interior wire and bracing commonly used on large bombers to allow passengers to walk freely through the streetcar style fuselage. Seating accommodates 18 passengers with eight additional folding seats when needed. For the first time, an enclosed cockpit design keeps the flight crew warm and dry by adding a roof and a Flexiglass front panel with a small sliding window on the co-pilot’s side. All previous airplanes in this era use the conventional open cockpit design. “Lawson Air Line” adorned each side of the fuselage in large letters.

Lawson C-2, Alfred Lawson, second from the left (photo courtesy PoorOldSpike)

On August 27, 1919, Alfred Lawson, “Captain in Command” along with his flight crew Charles Cox “Steersman,” Vincent Burnelli, Carl Schory “Engine Mechanic,” and Andrew Surini “Mechanic” departed the New Butler flying field in Wisconson headed to Ashburn Field in Chicago. Initially, the flight crew thought they were on a second test flight, but Lawson had other plans. Shortly after takeoff, Lawson ordered Cox to follow the shoreline of Lake Michigan south towards Chicago. “For one thing,” Burnelli later recalled, “we had planned on having several test flights; you just don’t build a plane from scratch in six months without encountering a bug here and there. For another, none of us had brought even so much as a toothbrush. Actually, however, we were all too excited and enthused to really care much where we went, although I doubt if I could say the same for our creditors in Milwaukee.” And so it begins, Alfred Lawson’s planned demonstration tour of the first airliner covering two thousand miles in over two months and ending on November 15, returning to the New Butler flying field. Shortly after this flight, Mr. Burnelli left Lawson Aircraft Company to pursue other avenues in his ever-challenging quest of designing and building the perfect aircraft.

The Lawson C-2 visited Bolling Air Force Base in September 1919, on its way from New York to San Francisco. (photo courtesy of U.S. Air Force)

1919 was a pivotal year for Mr. Burnelli when he changed his design approach from the conventional fuselage to his new airfoil-shaped fuselage stemming from his disappointment after his involvement and flight experiences with the Lawson C-2 biplane. The plane looked to him as a streetcar with wings. “The air is the roadbed of an airplane,” he said, “and I decided I’d leave streetcars on the ground from then on.” Being extremely fascinated with the flying wing and its efficiency, Mr. Burnelli started working on various transport designs of his “lifting body” wing type fuselages with twin tails or a tail-mounted on booms at the rear of the aircraft. He felt that these new fuselages could contribute about 40 percent of the lifting surface during flight and would be much safer in a stall or engine failure event. Not too mention the reduced structural loads on the wings, especially where the engines are mounted, and reduce the mortality rate in a crash due to the more robust flat rectangular shape of his fuselage. Mr. Burnelli’s design also places the engines well in front of the passenger compartment to help absorb the shock of a crash and locates the propellers away from the passengers. Another advantage is the flight crew’s partial access to the engines during the flight from inside the cabin.

(photo courtesy of

In 1920, Mr. Burnelli moved from Lincoln, Nebraska, back to Long Island, New York, after a brief career opportunity at the Nebraska Aircraft Company when he left Lawson. Again, he struggles with other people’s concepts and designs and decides it’s time to start working on building his perfect aircraft. Once settled back in New York, he partnered with T.T. Remington to initially form the Airliner Engineering Corporation, but later merged as the Remington-Burnelli Aircraft Corporation in the same year. There he could focus on building a large transport aircraft using his new lifting fuselage design. With little time to waste, he finishes the RB-1 biplane in 1921 with a successful maiden flight at Curtiss Field in Garden City, Long Island, New York, in June that same year. The slab-sided airfoil-shaped fuselage of the RB-1 has a cabin width of 14 feet and can carry a maximum of 32 passengers. A luxurious, spacious lounge divides the middle section. Comfortable chairs are positioned beside the windows on each side of the cabin for a breathtaking view. There are two entrance doors on each side of the fuselage with access towards the rear just behind the wings. A vestibule separates the passenger compartment from the baggage and express compartment located in the fuselage tail section for easy access. Twin 550 horsepower Galloway Atlantic engines mounted in the nose powered this large airplane with partial interior access panels for in-flight service if needed. Two open-air cockpits sit on top of the fuselage and provide a 360-degree field of view for the pilot and co-pilot. Throughout the remainder of the year and into 1922, Mr. Burnelli promoted his RB-1 through promotional advertising and scenic rides. The “Flying Festival” at the Curtis Field, where he stored the aircraft, was a popular event with a high turnout.

Burnelli RB-2, (photo courtesy kitchener.load)

An upgraded RB-1, the RB-2 Freighter was built in 1923 with improved control surfaces, twin 650 horsepower Galloway Atlantic engines provided more power, and corrugated metal construction replaces the fabric skin. It was the most significant transport aircraft ever built with an unladen weight of 5 tons and a gross vehicle weight of just under 9 tons! The passenger cabin could accommodate 25 people with standing headroom or converted to transport 6000 pounds of cargo with a flight crew of 3, the pilot, co-pilot, and mechanic.

Burnelli RB-2 w/Hudson Essex Logo (P Matt via Avn Heritage)

With no potential sales and difficulty in marketing, his business partner T.T. Remington departed the company in 1924. During the same year, Mr. Burnelli partners with Thomas Garvin to form the Garvin-Burnelli Aircraft Corporation. The new partnership focuses on promoting the RB-2 rather than building a new aircraft. In 1925 the RB-2 carried a Hudson Essex automobile built inside the cabin on an aerial sales tour flown at Mitchel Field, Long Island, New York. The passenger cabin also featured a fully equipped office and could carry eight passengers. Even with so much exposure, the RB-2 was slow, and Mr. Burnelli couldn’t generate interest for future investors or the financing that he desperately needed to finance production.

A few years have passed with no new interest in the RB-2, Mr. Burnelli is hired by banker and Skylines Incorporated president Paul B. Chapman in 1928 to build the CB-16 under contract on a progress payment basis for a total of $230,000 including design, engineering, and shop costs. He received the purchase order in May 1928, rented space and tools at the Aeromarine plant in Keyport, New Jersey, and completed the aircraft in December. The CB-16 was Mr. Burnelli’s first monoplane, single-wing, executive transporter with all-metal construction and retractable landing gear to reduce drag. It was accessible during flight for minor service or emergency release. The open cockpit design remains from the RB-2, but the CB-16 is the first multiengine aircraft capable of single-engine level flight in the event of an engine failure. A new twin-boom tail design is incorporated to correct stability issues encountered by the RB-2.

The CB-16 has a wingspan of 90 feet, a length of 56 feet, is 12 feet 6 inches in height, and has an empty weight of 11,400 pounds. The gross weight is 17,400 pounds, and two 625 horsepower Curtiss Conqueror engines supply the power with a cursing speed of 140 mph. The climb rate is 800 fpm, 300 fpm with a single-engine, and a ceiling of 20,000 feet. The cruising range is 12 hours, with a landing speed of 62 mph. For night flying, an ample center searchlight illuminates the pilot’s surroundings. With a spacious cabin measuring 12 feet by 18 feet, there is plenty of space for a large central lounge, ten swivel chairs, and soundproof luxurious tapestry and upholstery to finish the decor. An advanced air pressurization system maintains cabin ventilation and heating control while the unique washroom facility features running water. The stainless steel kitchenette has a hot plate and refrigerator with a radio in the center compartment.

A barge moves the unassembled pieces of the CB-16 to Newark Airport, which was still in construction at the time, to an available two-way cinder runway. The CB-16 is the first new design to be tested at the newly constructed airport, which officially opened on October 1, 1928, as the first major airport in the metropolitan area. With the assembly completed in December, a scheduled test flight occurs on a cold morning during Christmas week. Lieutenant Leigh Wade of Army ’round the world flight fame was at the controls with Jimmy Doolittle from Mitchel Field as a test collaborator. On that morning, Mr. Doolittle offered a parachute to Lt Wade. Still, he did not use it and instead brought along an assistant to operate the emergency release lever for the landing gear if they ran into trouble. Lt Wade landed after a successful 40-minute test flight and was eager to start performance tests the following day. Mr. Chapman chartered a bus on Christmas Eve to bring his friends to see his unique airplane, and Lt Wade offered to take anyone interested in a ride around the Statue of Liberty. When the aircraft landed, a line started to form for additional flights, and Lt Wade kept flying until dusk for four scenic flights carrying over a total of 50 passengers on this extraordinary holiday. In 1929, the CB-16 crashed during a test flight resulting from a maintenance error where the aileron cables malfunctioned. Thankfully, the pilot, Lt George Pond, and his co-pilot survived the crash, and it is a testament of how safe Burnelli’s fuselage designs are.

(photo courtesy

Mr. Burnelli designed and built many more unique airplanes, the UB-20, the GX-3, and the CBY-3, to name just a few. He continued to promote his airfoil-shaped fuselage designs throughout his life but could never sell his ideas for mass production. He is a true pioneer in aviation history, and some people consider him a revolutionary genius. I hope you enjoyed my post on the CB-16, and I encourage you to research the life of Vincent Burnelli and his innovative lifting designed fuselages. You won’t be disappointed, and maybe I’ll find a few more clippings in my father’s scrapbook on him to share with you.

Burnelli CBY-3 Loadmaster restored (photo courtesy NEAM)

Vincent J. Burnelli passed away at age 69 on June 22, 1964 (as reported by The New York Times on June 23, 1964, page 33).

Cessna Cutlass/Cutlass RG

1984 Cessna Cutlass

Cessna introduced the Cutlass and Cutlass RG models in 1980 and ceased production in 1985. Both models are built on the popular and proven 172 Skyhawk airframe with the addition of the upgraded Lycoming O-360 engine, a variable pitch constant speed propeller, and the optional retractable landing gear on the RG models.

1984 Cessna 172 Skyhawk

The Cutlass featured a Lycoming O-360-A4N 180hp engine with a cruise speed of 122 knots. The useful load increased by about 100 pounds over the 172 Skyhawk.

1984 Cessna Cutlass RG

The Cutlass RG model has a Lycoming O-360-F1A6 with the same 180 hp but allows for clearance with the front wheel retracted. The RG uses the same electro-hydraulic landing gear in the Skylane RG, and the cruise speed increased to 140 knots. Combine this with larger fuel tanks than the 172, and you have a better cross-country airplane! The RG is an excellent platform for pilots working on their commercial certificate or complex endorsement.

Be sure to check out more photos of the Cessna Cutlass/Cutlass RG on the Aircrafts Photo page or through this link.

Cessna 177 Cardinal RG

Cessna introduced the 177 Cardinal in 1968 and, production only lasted for ten years. They were seeking a replacement for the popular 172 and thought this would be an excellent time to introduce a new model. The popularity of the 172 was too much for the Cardinal combined with poor performance and handling problems.

Cessna’s most popular airplane, the 172 Skyhawk!

The primary issue first reported in 1968 is pilot induced oscillations or “porpoising.” These are a series of pilot corrections to airplane reactions that result in sustained or uncontrollable swings. Cessna addressed the problems and offered a no-cost warranty to existing owners to fix these problems.

Cessna’s goal for the Cardinal is to allow the pilot an unobstructed view when turning but resulted in a too far forward CG since the pilot is seated ahead of the leading edge. The first model year featured a lighter engine, the Lycoming O-320, which was vastly underpowered but did address the forward CG issue. The Lycoming O-360 engine replaced the O-320 in 1969 but retained the fixed-pitch propeller, which helped reduced production costs.

The Cardinal uses a cantilever wing design, which eliminates the lift struts for better visibility. A stabilator replaces the standard horizontal stabilizer to resolve issues of elevator control at low airspeeds. The raked windshield and aft-mounted wing allow for better upward visibility combined with the cantilever wing make this airplane a photographer’s dream!

Cessna began production of the Cardinal RG in 1971 and featured an electrically powered hydraulic retractable landing gear. The horsepower increased from 180 to 200 with a new Lycoming IO-360 engine because of the added weight of the landing gear system.

Compare the differences of this 1973 Cessna Cardinal RG to the above photo of the 1968 Cessna 172 “Skyhawk.” Notice the different wing designs, windshields, and landing gears. I’ve only found one picture of a Cessna Cardinal RG so far, and I’ll add any new photos to this post if I see others.

Cessna Stationair and Centurion

I recently added new photos that I recently scanned of old promotional pictures that were at Buffalo Air-Park. These are of the larger Cessna “mini-van/sport-utility” airplane, the Stationair, and the Centurion. The Stationair consisted of the 205, 206, and 207 models, while the Centurion is the 210 model. I did find a 207 Skywagon, Cessna later renamed to the Stationair 7, and included it with the Stationair pictures. It’s awe-inspiring the amount of cargo/passenger space in the 207 Skywagon!

I’m glad that I never had to clean one of these airplanes!

Check out more photos of the Cessna Stationair on the photos page or through this link.

The 210s were more popular over the Stationairs when I was working the line at the air-park during the early 1980s, and I loved watching the retractable gear on them after takeoff. It was quite an impressive sight! Luckily, I only had to wash and detail a couple of 210s, but hand waxing a 152 wasn’t any easier.

Cessna introduced the 210 in 1960 with a strut-braced wing but later changed to a strutless cantilever wing in 1967. This new wing design reduces drag, improves visibility, and generally gives the airplane a cleaner appearance. But it does come at a cost. All of the bracings are internal, which places tremendous force on the spar cap, wing spar, and the whole structure. In 2012 the FAA mandated all cantilever winged 210s to be inspected for cracks in these critical areas.

1967 is the first year of the strutless cantilever wing on the 210s.

Here’s the link for more photos of the Cessna 210 on the photos page. Enjoy!

The Cessna Skywagon

Where to start with the Cessna Skywagon? I’ve learned quite a lot about Cessna, and the many different names or model numbers that refer to the same aircraft when scanning these promotional photos. It’s no surprise with the Skywagon, and hopefully, I can explain what I’ve learned so far.

This photo wasn’t dated, but notice the 2 side windows. It must be pre-1963!

Cessna started branding the “Skywagon” name on their 180 airframes in the early 1960s, even though the 180 models began production in 1953. The 180 is a taildragger with steerable tailwheel and steel spring main gear legs. The models produced before 1963 have two side windows and three starting in 1964 when Cessna upgraded the airframe to the same one used on the 185s but retained the lower horse-powered carbureted Continental O-470-R engine. This engine is rated to have 230hp at 2600 rpm while the IO-470-F used on the 185s has 260hp and is fuel injected.

This airplane has 3 side windows and seating for 6 people.

The earlier 180, 1953-1963, is a four-person aircraft with the optional “Family Seating” for six people at an additional cost. I can only assume the seating was tight with this option, and I wouldn’t want to be sitting in the back for any length of time. The later 180, 1964-1981, is certified as a six-place utility airplane with the ability to install the optional floats or skis.

1967 Cessna 185 Skywagon

The production run of the 185 Skywagon is from 1961 to 1985. The 185 Skywagon gained many improvements over the later 180 when Cessna upgraded the powerplant to the Continental IO-520-D engine, but not until the middle of the 1966 production year. The previous 185s were still using the IO-470-F engines. Floats and skis were still an option along with a cargo pack that attached to the bottom of the fuselage.

1978 Cessna AGcarryall

The “AGcarryall” is a variant of the 185 and has a 151-gallon belly tank with removable spray booms for aerial spraying. The high wing design made it difficult to see when turning for crop dusting, and the production run was short. The “Agwagon” was well established and better suited for aerial chemical applications.

Be sure to check out the many photos of the Cessna Skywagon that I recently added to the photos page!

Cessna 180 Skywagon photos

Cessna 185 Skywagon photos

Cessna Super Skywagon photos